Smart Ring |Care & Maintenance

Keep every wear fresh and comfortable.

Everyday care starts with three simple habits. Before cleaning, remove the ring and disconnect charging accessories from power.

Promptly clean contact surfaces
Keep the ring dry
Avoid impacts and unsuitable environments
01

Daily Cleaning: Wipe Gently, Never Scrape

  1. 1Use a soft, clean, lint-free dry cloth to gently wipe the outer ring, inner ring, and visible sensor surfaces.
  2. 2Check the inner ring for sweat residue, hand cream, or other deposits. Do not scrape off dirt with fingernails, needles, blades, or stiff brushes.
  3. 3For dirt that cannot be removed with a dry cloth, follow a cleaning method approved for your model. Use a slightly damp soft cloth or specified cleaning products only when expressly permitted in your model's instructions. Do not otherwise soak or rinse the ring.
  4. 4After cleaning, check for remaining moisture or residue. Allow the ring to dry completely before wearing or charging it.

Check the ring promptly when you notice dirt, after sweating, or after contact with personal care products. There is no need to rub it frequently or forcefully just to keep it clean.

02

Inner Ring & Sensors: Keep Clean, Do Not Disassemble

The inner ring is in direct contact with your skin. Pay particular attention to residue on and around visible sensor surfaces. Wipe gently. Do not dig into gaps, remove components, or try to peel off any covering layer.

If recordings remain unusual after cleaning, first check the fit, connection, and synchronization status. Do not repeatedly clean with stronger agents or greater force. Contact customer support if needed.

03

After Sweat or Water Exposure: Dry Before Wearing Again

  • After sweating during exercise, remove the ring and dry the ring and your finger separately. Put it back on only when your skin and the inner ring are clean and dry.
  • After washing your hands or accidental water exposure, follow your model's water-resistance and care instructions. Do not assume that a water-resistance rating also covers swimming, seawater, hot water, steam, or high-pressure water jets.
  • After contact with seawater, pool water, or cleaning agents, remove residue as directed in your model's instructions. Do not add rinsing or soaking steps unless the cleaning method has been confirmed.

Do not use hot air from a hair dryer, a heater, an oven, or strong sunlight to speed up drying. If you suspect liquid ingress or notice anything unusual, stop wearing and charging the ring and contact customer support.

04

Charging Accessories: Disconnect Power Before Checking

  • Disconnect power and remove the ring before cleaning a charging dock, charging case, or cable.
  • Use a dry, soft cloth to wipe accessory exteriors and accessible charging areas. Do not drip cleaning liquid into ports or use metal objects to clean the contacts.
  • Do not assume that charging accessories have the same water resistance as the ring. Use them as directed in the charging instructions only after the ring, charging contact areas, and accessories are completely dry.
  • Use accessories supplied for your model or explicitly confirmed as compatible. Do not interchange charging docks merely because they look similar.

If you notice damage, corrosion, significant deformation, an odor, or unusual heat, stop using the accessory and contact customer support. Do not repeatedly power it on to test it.

05

Protect the Surface: Reduce Rubbing, Impacts & Pressure

  • Remove the ring before lifting heavy objects, gripping metal equipment, operating machinery, or doing anything that could snag it.
  • Store it separately from keys, coins, and other jewelry to prevent hard objects from rubbing against it.
  • If the surface becomes scratched, do not sand, polish, repaint, or apply protective coatings yourself. Minor wear and structural damage should be assessed separately. If you notice cracks, sharp edges, loose parts, or deformation, stop wearing the ring and contact customer support.
  • Do not use alcohol, disinfectants, bleach, solvents, or abrasive cleaners unless permitted in your model's instructions. Do not use ultrasonic cleaners or high-temperature steam cleaning.
06

Turn Off the Ring Before an Extended Break

If you expect not to wear the ring for a week or longer, make sure its battery level is at least 80% before turning it off through the App, and confirm that it has powered off successfully. Do not wait until the battery is depleted before putting it away. Turning off your phone's Bluetooth does not turn off the ring.

Before Putting It Away: Follow These Steps in Order

  1. 1Sync your data.Turn on your phone's Bluetooth, connect to the ring in the App, and sync the latest data. Keep the connection active until the power-off operation is complete.
  2. 2Check the battery level.Make sure the ring’s battery level is at least 80% before storage. If charging is needed, finish charging first, then remove the ring from the charger.
  3. 3Turn off the ring.Select “Power Off” in the App, read the prompts, and confirm. The exact location of this option depends on the current App interface.
  4. 4Confirm success.Wait for the App to confirm that the ring has powered off successfully. A disconnected Bluetooth connection or an offline device status alone does not confirm this. If no success message appears, check the connection and retry as prompted in the App.
  5. 5Put the ring away safely.Once powered off, the ring will disconnect from the App via Bluetooth. You do not need to turn off your phone's Bluetooth beforehand. Keep the clean, dry ring in a cool, dry place away from heat sources, children, and pets. Do not leave it on the charger.

When Using It Again: Charge to Power On, Then Reconnect via Bluetooth

  1. 1Check that the ring and charging accessories are undamaged, clean, and dry.
  2. 2Connect the ring to a compatible charger connected to power. The ring will turn on automatically.
  3. 3Turn on your phone's Bluetooth, reconnect to the ring in the App, and check the battery level and device status. Wear it again only after confirming that everything is normal.

Important: Charging automatically turns the ring on. Even if you are only topping up the battery, finish charging, remove the ring from the charger, then turn it off again through the App and confirm success. Removing the ring from the charger does not automatically turn it off.

Keeping the Ring Safely & Checking It Periodically

Avoid direct sunlight, hot vehicle interiors, damp bathrooms, and pressure on the ring. While the ring is powered off and stored, recharge it to at least 80% every 2 months, then turn it off again through the App. If the ring still cannot connect or charge when brought back into use, contact customer support. Do not disassemble it or replace the battery yourself.

07

What to Do if You Notice a Problem

  • Skin redness, itching, stinging, or broken skin — Stop wearing the ring. Check the fit and whether the contact surfaces are clean and dry. Seek medical help if discomfort persists or worsens.
  • Cracks, deformation, or sharp edges on the ring — Stop wearing it to prevent further rubbing against your skin.
  • Unusual heat, an odor, swelling, or suspected liquid ingress — Stop wearing and charging it. Do not disassemble, squeeze, or continue testing it.
  • Stains that cannot be removed, or corrosion in charging areas — Do not scrape or use strong cleaning agents. Contact after-sales support.

When contacting customer support, have your model, photos of the problem, the time it occurred, and details of any environments or products the ring was exposed to ready. This helps determine the next steps.

08

Frequently Asked Questions

QCan I disinfect the ring with alcohol every day?

ADo not use it unless permitted. Exterior materials, coatings, and contact areas may vary by model. Refer to your model's instructions to check whether alcohol or other cleaning products are allowed.

QCan I put a water-resistant ring directly in water to clean it?

AWater resistance alone does not determine this. Check your model's instructions separately for whether soaking, rinsing, and cleaning agents are permitted.

QCan I apply hand cream while wearing the ring?

AWe recommend removing the ring first and putting it back on once there is no noticeable residue on your skin. Clean any residue on the inner ring using the specified method.

QWill scratches affect use?

AAppearance alone cannot determine this. Do not attempt repairs yourself. If you notice cracks, deformation, sharp edges, or abnormal operation, stop using the ring and contact after-sales support.

QCan I leave the ring on the charger whenever I am not wearing it?

AThis is not recommended. Charging automatically turns the ring on. If you will not be using it after recharging, remove it from the charger, turn it off again through the App, and confirm success.

QDoes turning off my phone's Bluetooth turn off the ring?

ANo. You must select “Power Off” in the App and receive a success confirmation. Do not manually disconnect Bluetooth before the power-off command has completed.

QWhat if the App cannot find the ring after it has been turned off?

AThis is normal when the ring is powered off. First connect it to a compatible charger connected to power to turn it on. Then turn on your phone's Bluetooth and connect in the App. Contact customer support if you still cannot connect.

QDo I need to turn the ring off again after topping up the battery?

AYes, if you will not be using it. Charging automatically turns the ring on. After recharging, remove it from the charger, turn it off again through the App, and confirm success.

This guide provides general care and maintenance information. Follow the instructions for the model you purchased regarding cleaning products, permitted water exposure, and accessory compatibility.